欧盟Eurlex法规详细信息

EURLEX ID:32012D0201

OJ编号:OJ L 109, 21.4.2012, p. 20-21

中文标题:委员会实施决定2012/201/EU,修订委员会决定98/213/EC,该条例关于对内部隔离组件,依据理事会指令89/106/EEC第20(2)条证明建筑产品符合性的程序(通报文件号C(2012) 1866)?(1)

原文标题:2012/201/EU: Commission Implementing Decision of 26 March 2012 amending Decision 98/213/EC on the procedure for attesting the conformity of construction products pursuant to Article 20(2) of Council Directive 89/106/EEC as regards internal partition kits (notified under document C(2012) 1866) Text with EEA relevance

分类:423

文件类型:二级立法 Decision|决定

废止日期:2058-12-31

法规全文:查看欧盟官方文件

L 109/20
EN
Official Journal of the European Union
21.4.2012
DECISIONS
COMMISSION IMPLEMENTING DECISION
of 26 March 2012
amending Decision 98/213/EC on the procedure for attesting the conformity of construction
products pursuant to Article 20(2) of Council Directive 89/106/EEC as regards internal partition kits
(notified under document C(2012) 1866)
(Text with EEA relevance)
(2012/201/EU)
THE EUROPEAN COMMISSION,
HAS ADOPTED THIS DECISION:
Having regard to the Treaty on the Functioning of the European
Article 1
Union,
Decision 98/213/EC is amended as follows:
Having regard to Council Directive 89/106/EEC of 21 December
(1) the following Article 3a is inserted:
1988 on the approximation of laws, regulations and adminis
trative provisions of the Member States relating to construction
‘Article 3a
products ( 1 ), and in particular Article 13(4) thereof,
The procedure for attesting conformity as set out in Annex
IV shall be indicated in mandates for harmonised European
After consulting the Standing Committee on Construction,
standards.’;
Whereas:
(2) Annex IV is added, the text of which is set out in the Annex
to this Decision.
(1) Commission
Decision
98/213/EC
( 2 ) only refers to
products as defined in European technical approvals,
Article 2
while some of those products may also be covered by
This Decision is addressed to the Member States.
harmonised European standards.
(2) The
European
Committee
for
Standardisation
(CEN)
is Done at Brussels, 26 March 2012.
currently preparing harmonised European standards for
certain products referred to in Decision 98/213/EC.
For the Commission
(3) Decision
98/213/EC
should
therefore
be
amended
Antonio TAJANI
accordingly,
Vice-President
( 1 ) OJ L 40, 11.2.1989, p. 12.
( 2 ) OJ L 80, 18.3.1998, p. 41.

EN
21.4.2012 Official
Journal
of
the
European
Union L
109/21
ANNEX
‘ANNEX IV
PRODUCT FAMILY
GYPSUM BOARD PARTITION KITS (1/2)
Systems of attestation of conformity
For the product(s) and intended use(s) listed below, the European Committee for Standardisation (CEN) is requested to
specify the following system of attestation of conformity in the relevant harmonised European standards:
Product(s) Intended
use(s) Level(s)
or
class(es)
Attestation of conformity
system(s)
Internal partition kits/systems For
all
uses
not
subject
to
any
3
reaction to fire requirements
System 3: See Annex III(2)(ii) to Directive 89/106/EEC, second possibility.
The specification for the system must be such that it may be implemented even where it is not necessary to determine the
performance for a certain characteristic, because at least one Member State has no legal requirement for that characteristic
(see Article 2(1) of Directive 89/106/EEC and, where applicable, point 1.2.3 of the interpretative documents). In those
cases, the verification of such a characteristic must not be imposed on the manufacturer if it does not wish to declare the
performance of the product in that respect.
PRODUCT FAMILY
GYPSUM BOARD PARTITION KITS (2/2)
Systems of attestation of conformity
For the product(s) and intended use(s) listed below, CEN is requested to specify the following system(s) of attestation of
conformity in the relevant harmonised European standard:
Product(s) Intended
use(s)
Level(s) or class(es)
Attestation of conformity
(reaction to fire)
system(s)
Internal partition kits/systems Uses
subject
to
reaction
to
fire A1 (*), A2 (*), B (*), C (*)
1
requirements
A1 (**), A2 (**), B (**),
3
C (**), D, E
(A1 to E) (***), F
4
System 1: See Annex III(2)(i) to Directive 89/106/EEC, without audit-testing of samples.
System 3: See Annex III(2)(ii) to Directive 89/106/EEC, second possibility.
System 4: See Annex III(2)(ii) to Directive 89/106/EEC, third possibility.
(*) Products or materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire
classification (for example, the addition of fire retardants or the limitation of organic material).
(**) Products or materials not covered by footnote (*).
(***) Products or materials that are not required to be tested for reaction to fire (for example, products or materials of Class A1 in
accordance with Commission Decision 96/603/EC (OJ L 267, 19.10.1996, p. 23)).
The specification for the system must be such that it may be implemented even where it is not necessary to determine the
performance for a certain characteristic, because at least one Member State has no legal requirement for that characteristic
(see Article 2(1) of Directive 89/106/EEC and, where applicable, point 1.2.3 of the interpretative documents). In those
cases, the verification of such a characteristic must not be imposed on the manufacturer if it does not wish to declare the
performance of the product in that respect.’

Document Outline


附件:

P020171219248888391816.pdf

触碰右侧展开